Laminating Tips

Learn time-tested procedures for trouble-free laminating of digital prints.

There’s usually more than one way to do something.  Printers and sign makers have devised many different techniques for laminating prints. This story covers procedures that have worked for some industry friends. Hopefully, these tips will help you prevent laminating mishaps, save production time and, most importantly, improve profitability. 

 Photo courtesy of Molly Waters of Avery Dennison.

Laminating Equipment Safety Procedures.

Review the safety precautions outlined in the equipment manual with your employees. Never wear loose clothing when operating the machinery. Long hair should be tied back. Wearing a hair net could prevent hair from falling onto a print and being encapsulated.

Keep your hands away from any moving parts. If you’re wiping down the rubber rollers, disconnect the power — this prevents accidents from occurring, especially if the laminator is accidentally turned on. If you need to advance the rollers, reconnect the power. After you’ve advanced the rollers, pull the plug again. Use a clean, lint-free rag and a mild, non-abrasive cleaner to wipe down the laminator.

Component Compatibility. 

The interaction of inks, printing systems and print media involves very complex chemistry. Incompatibility among components can adversely affect the ability of the overlaminate to adhere to the print and result in delamination. 

TEST, DON’T GUESS. Always test and evaluate your raw materials (overlaminate, print media, and mounting substrate) before a production run. When you find a winning combination, stick with it. 

One recommended combination is using a calendered vinyl overlaminate with a calendered vinyl film and a cast vinyl overlaminate with a cast vinyl film. Similar films expand and contract at the same rate. Dissimilar films don’t. As a consequence, the overlaminate can delaminate from the base film or substrate.  A tunnel could also form between the two dissimilar films.

Overlaminate problems can also result when a print is mounted to a substrate that expands and contracts at a high rate.  The resulting tension between the print and the laminating film, can cause tunneling or delamination.

Storage of  Overlaminates. 

There are right ways and wrong ways to store overlaminates and other pressure sensitive materials, such as application tape and vinyl.  The wrong way is to stack the rolls of unboxed overlaminates horizontally on top of each other.  Doing this can create flat spots in the rolls, which can appear as a visible line, after the overlaminate is applied to the print. 

The recommended way to store rolls is to keep them in their boxes, stacked upright, until you need them. Although the corrugated containers used for overlaminates are designed to withstand the rigors of shipping, stacking these boxes horizontally can result in their collapse, when weight becomes excessive.   

The best storage area is the same one in which you print. An ideal temperature and humidity controlled room is at 70°F (21°C) at 50% relative humidity. Under these conditions, the expected shelf life of your RTape Eclypse™ overlaminates  is +1 years. 

Shop environment.  

Along with being spotlessly clean, the ideal shop is temperature and humidity controlled. In cleaning your machinery, never use an air hose. Much of the blown off dirt goes airborne and eventually settles on your raw materials. Dirt trapped between the print and the overlaminate usually results in tenting of the laminating film over the trapped particle. To clean the rollers of your laminator, try using a tack cloth. 

Print Drying Time. 

Before applying an overlaminating film to your print, be sure the ink on the print is completely dry. If the ink is not cured, some of the problems that can ensue are: bubbles under the laminate; yellowing of the media and overlaminate; migration of solvents through a vinyl film and into the adhesive, causing adhesion failure.  Two good rules of thumb are to wait 24 hours before laminating the print, so the inks can cure properly; and before mounting or rolling up the laminated print, let it lay flat for 24 hours. 

Print drying time varies, depending on the print’s ink density, the ambient temperature and your shop’s humidity Even though the print feels dry to the touch, the ink may not be completely cured.  The time it takes for a print to dry varies depending on the density of the ink on the print, ambient temperature and the humidity in your shop. Usually, inks take longer to dry, when temperatures are cooler and the humidity is high. Consult the manufacturer’s recommendations on drying time. 

Threading the Laminator.  

Before threading the overlaminate through the machine, study the roll-laminator diagram in your owner’s manual. The laminated print’s finished appearance depends upon several variables, including the feed roller’s unwind tension, the nip rollers’ pressure, laminating speed and temperature. 

 

Before threading the overlaminate through the machine, study the roll-laminator diagram in your owner’s manual. Photo courtesy of Molly Waters of Avery Dennison.

All laminators are different, so you must determine your machine’s optimum settings. After you load the overlaminate roll onto the unwind shaft and secure it in place, make sure the roll can’t shift from side to side. The tension on the unwind roll should be low. As a general rule, use the least amount of tension to accomplish the job.

Don’t allow the unwind roller to free-wheel. A slight amount of tension ensures that the overlaminate feeds into the nip rollers evenly. Some back tension will prevent wrinkling and trapped air bubbles.

High unwind tension stretches the overlaminate. Any stretched film, especially a stiff film like polyester, has a memory and tends to return back to its original shape. This can cause the laminating film to either curl in the direction of, or delaminate from, the print. Excessive tension can also contribute to delamination of the print from the substrate to which it’s mounted.  High unwind tension and high laminating pressure can result in the print curling.

Laminator Set Up. 

Don’t expect satisfactory laminating results, if your laminator is not set up properly.  Regularly inspect the laminator rolls to see that they are in good condition and adjusted properly. Rolls, which are not perfectly smooth and parallel, and not adjusted so the pressure is consistent across the web, can cause problems.  These problems include trapped air bubbles, wrinkling and poor adhesion.

Adjusting roll pressure so that it is consistent across the web can frustrating, if your machinery has adjustment screws, instead of using air cylinders for adjustment.   

Laminator manufacturers typically recommend periodic testing of the laminator “footprint”, which requires a special nip impression transfer paper.  In checking the footprint of the rolls, sheets of the nip impression paper are positioned across the web.  After the rolls are hot, close them for ten seconds. After removing the sheets, inspect the impression for consistency. Inconsistent impressions will reveal any unevenness in pressure across the roll.  Uneven pressure can result from rolls which have either a concave or convex shape or that are canted. Nip impression paper can be purchased from the Beloit Manhattan Division, Clarks Summit, PA 18411 (717-587-5111)

Laminating Techniques. 

Printers have developed many different laminating techniques. Per se, there is no wrong way or right way to laminate. If you find a technique that works for you, continue to use it.  Here’s one that you might try.  Slit the release liner, 18 to 24 in. (45.7cm to 61cm) from the overlaminate’s lead edge, across the web, without cutting through the facestock of the film.        Don’t remove the liner from these first couple of feet of overlaminate. This lead edge will aid film feeding and prevent the adhesive from sticking to, and wrapping around, the bottom roller.

Next, from the slit you’ve made, peel back enough liner so you can tape it to the take-up shaft (if your laminator is equipped with one). As you guide the overlaminate through the rollers, ensure that the material is feeding evenly, and that no wrinkles or bubbles are forming. During startup, you likely wasted a few feet of overlaminate.

Once everything is running smoothly, you can feed the prints into the laminator. Laminating prints is always easier if one person stands in front of the machine and feeds the print, and another person guides the laminated print and prevents the laminate from wrapping around the rollers.

Apply laminating film to a print in one continuous pass. And, whatever you do, don’t stop in the middle of a print to see how it’s going.  Starting and stopping during this process will pick up the impression of the release liner — at the point where the liner and film separate — causing silvery lines in the adhesive and over the print. This is especially noticeable over the print’s dark “shadow” areas. Note that, in most cases, this problem can be easily fixed by burnishing the line with your thumb nail to aid the adhesive in wetting out.

Laminator Speed and settings. 

Pressure-sensitive films usually laminate better at slower speeds. Thus, set your laminator’s machine speed to 3 to 5 ft. (.9m to 1.5m) per minute. Then set the machine’s pressure-control gauge, which governs the nip rollers’ pressure.

Pressure-sensitive overlaminates require pressure so the film’s adhesive properly flows out and makes complete contact with the print’s surface. Insufficient pressure can result in silvering and air-bubble formation. Conversely, excessive pressure can cause print wrinkling and curling.

Requisite pressure for applying a laminating film varies. Overlaminates generally require between 30 to 50 psi (2.1 to 3.5Kg/cm) of pressure. If air bubbles appear, you can increase the nip pressure, slow the laminating speed, and, if worse comes to worse, apply a little heat.

Thicker overlaminates, such as 5-, 10- and 15-mil (125-, 250– and 375 micron) polycarbonate films, typically require higher pressure settings. When laminating graphics with these films, using a “sled” (which comprises an 1⁄8-in. (.3cm) sheet of polycarbonate or acrylic) underneath the print can increase pressure and even out the pressure across the laminator’s web.

Should you use heat when laminating a pressure-sensitive film? Some people argue that, with a little heat on the top roller — from 80 to 110°F  (26.6 to 43.3°C) — the overlaminate’s adhesive flows out better, which creates a better bond to the print and can prevent silvering.

An opposing argument says that heat can cause the overlaminate to stretch.  As the overlaminate cools, it contracts, causing the laminating film to shrink and in some cases delaminate from the print. The shrinking film quite often causes the print to curl to the print side. Heat can cause other problems too, including waviness, tunneling and wrinkles. Thus, it’s best not to use heat, unless you have a serious problem. 

Rolling Laminated Prints. 

Whenever possible, store and ship prints flat, especially when using polyester overlaminates. Generally, a flexible overlaminate, such as vinyl, is preferred for rolled graphics. If you need to roll a print, place the printed image on the outside of the roll. Never roll a print too tightly, or you’ll end up with tunneling between the overlaminate and print.

When rolling up a printed vinyl film with a vinyl overlaminate, the  outside diameter of the core should be no less than 6 in. (15 cm). When rolling graphics, which are protected with a thick (5 to 15 mils, i.e., 125 to 375 microns) vinyl or polycarbonate overlaminate, the interior roll should be no less than 12 in. (30cm) in diameter. Basically, the thicker the overlaminate, the larger the core diameter.

Cleaning Laminated Prints. 

Before delivering prints to customers, instruct them how to properly care for their new graphics. To clean laminated prints, use a mild, non-abrasive cleaner — one that doesn’t contain a lot of acid or alkaline, or a strong solvent.  When washing graphics, use a sponge or soft rag. Hard, bristle brushes will scratch an overlaminating film’s — especially 3-mil (75 micron) PVC films — surface. To dry graphics, use a soft, clean cloth towel. Drying with a dry paper towel could also scratch the overlaminate.

Visit My Vinyl Sign Techniques Community

Related Articles

How to Select the Right Overlaminate
Laminating Tips: Silvering
Choosing a Floor Graphics Overlaminate
Mottling and what to do about it

Vinyl Application Videos

Squeegee Technique. Nothing is more basic in vinyl application than the squeegee. But some squeegees work better than others. And there are right ways and wrong ways to use this simple tool. This video clip reviews squeegee selection, squeegee care and squeegee technique. Click to Link

Wet Applications. Dry applications are typically recommended for most vinyl applications. For those exceptions to the rule, this instructional video explains the right way to perform a wet application. Click to Link

Application of Window Graphics. Installing vinyl graphics on glass can be challenging, because the adhesive aggressively grabs onto this high energy surface. Repositioning graphics on window is generally difficult, if not impossible. This instructional video explains how to dry apply window graphics right the first time. It also describes the necessary steps required for surface preparation. Click to Link

Transferring Frosted Window Graphics Films.  Because frosted window films are highly textured, transferring cut vinyl graphics can be problematic. This video provides direction in selection of the right application tape and how to apply these films quickly, easily and without problems. Click to Link

3-Step Surface Prep. This instructional video describes how to properly clean the surface of a vehicle before applying pressure sensitive vinyl graphics to a trailer or doing a full wrap of a car or van. This three step surface prep involves detergent washing, solvent cleaning and a final wipe down with IPA. Click to Link

Vinyl Application Over Rivets. Applying vinyl graphics on vehicle surfaces with rivets is challenging for most sign makers. Vinyl failures to these surfaces are all too common. This video demonstrates some tips and procedures, used by professional decal installers, which will make these demanding applications easier and more trouble-free.  Click to Link

Vinyl Application to Corrugations. Learn how to apply vinyl graphics to corrugations in a relaxed state. Forcing films into the valleys of corrugations puts too much mechanical stress on the film. Sooner or later, the vinyl will lift or tent in valleys. Click to Link

Applying Air Egress Vinyls. Vinyl films with air egress release liners have almost eliminated bubbles and wrinkles from applied graphics. Air egress release liners with their highly textured surface structure are problematic. Not much will stick to these liners other than the vinyl film. At RTape our best premask solution for air egress liners is a special Conform® tape called 4761RLA. Click to Link

About Jim Hingst: After fourteen years as Business Development Manager at RTape, Jim Hingst retired. He was involved in many facets of the company’s business, including marketing, sales, product development and technical service.

Hingst began his career 42 years ago in the graphic arts field creating and producing advertising and promotional materials for a large test equipment manufacturer.  Working for offset printers, large format screen printers, vinyl film manufacturers, and application tape companies, his experience included estimating, production planning, purchasing and production art, as well as sales and marketing. In his capacity as a salesman, Hingst was recognized with numerous sales achievement awards.

Drawing on his experience in production and as graphics installation subcontractor, Hingst provided the industry with practical advice, publishing more than 150 articles for  publications, such as  Signs Canada, SignCraft,  Signs of the Times, Screen Printing, Sign and Digital Graphics and  Sign Builder Illustrated. He also posted more than 325 stories on his blog (hingstssignpost.blogspot.com). In 2007 Hingst’s book, Vinyl Sign Techniques, was published.  Vinyl Sign Techniques is available at sign supply distributors and at Amazon. 

© 2016 Jim Hingst