Laminating Tips: Silvering

Learn what silvering is and how to minimize the occurrence of this problem.

Have you ever seen silvery specs in a laminated print? This defect is called silvering. It’s caused when tiny air bubbles are captured between the adhesive on an overlaminating film and the surface of a print. Silvering is generally most noticeable in the dark shadow areas of a print.

Silvering frequently occurs when laminating UV-curable inkjet prints. There is good reason for this, too. UV inks cure immediately, so there’s no time for the ink to level out. Instead of a smooth finish on the print, UV inkjet prints have a rough, velvety texture.

Ideally, the adhesives on  overlaminates should be formulated to flow into that textured surface of the print. If the adhesive flows out properly, you should not have silvering problems.  One way to achieve good adhesive flow out is coating the overlaminating film with a   heavier coat weight. With more mass, the adhesive will more readily flow into the recesses of the textured surface of the print.

Silvering is more prevalent with polycarbonate overlaminates used on  UV printed graphics. Although the adhesive on these films is thicker, it is also harder.  These harder adhesives will build to higher ultimate adhesion values. But they will not wet out the way a softer adhesive will.

There are, of course, tips  for minimizing silvering:

PRESSURE SETTING. 

Pressure sensitive overlaminates need pressure so the adhesive on the film properly flows out and makes complete contact with the surface of the print. Inadequate adhesive wetting can result those troublesome silvery bubbles. The amount of pressure needed in applying a laminating film can vary from film to film. RTape Eclypse™ overlaminates generally require between 40 and 100psi of pressure. If air bubbles appear, possible solutions include:

● Increasing the nip pressure;

● Slowing the laminating speed, and,

● If worse comes to worse, using a little heat.

TEMPERATURE. 

Low shop temperatures can contribute to the occurrence of silvering. Using a little heat can help. Adjusting the heat on the top roller (from 80°F to 110°F), can help the adhesive on the overlaminate flow out better. Generally, the rule of thumb is not to use heat, unless you have a problem.

LAMINATOR SPEED SETTING. 

Pressure-sensitive films usually laminate better at slower speeds. Thus, set your laminator’s machine speed to 3 to 5 ft. per minute. Then set the machine’s pressure-control gauge, which governs the nip rollers’ pressure. Pressure-sensitive overlaminates require pressure so the film’s adhesive properly flows out and makes complete contact with the print’s surface. Insufficient pressure can result in silvering and air-bubble formation.

USING A SLED. 

Thicker overlaminates, such as 5-, 10- and 15-mil polycarbonate films, typically require higher pressure settings. When laminating graphics with these films, using a “sled” (which comprises an 1⁄8-in. sheet of polycarbonate or acrylic) underneath the print can increase pressure and even out the pressure across the laminator’s web.

ADDITIONAL TIPS

DON’T STOP ONCE YOU START. 

Applying a laminating film to a print should be done in one continuous pass. Whatever you do, don’t stop in the middle of a print to see how it’s going. You’ll only end up with a flat spot in the adhesive, which can result in streaks and air pockets.

TEST, DON’T GUESS. 

The interaction of inks, printing systems and print media involves very complex chemistry. Incompatibility among components can adversely affect the ability of the overlaminate to adhere to the print and result in delamination. Always test and evaluate your raw materials (overlaminate, print media, and mounting substrate) before a production run. When you find a win-ning combination, stick with it.

CURING TIME. 

Humidity in your customer’s shop can affect their finishing job. High levels of humidity can prolong the time it takes for a print to dry. Laminating a print before it is thoroughly cured can result in solvents and moisture being trapped between the media and the overlaminate. To minimize problems caused by high humidity, shops should maintain the humidity within their shops between 20% and 50%. Before laminating, allow enough time for the print to dry. To aid drying, direct fans on printed graphics. After laminating, let prints lie flat for 24 hours before rolling to allow the adhesive system of the overlaminate to completely wet out on the surface of the print.

Vinyl Application Videos

Squeegee Technique. Nothing is more basic in vinyl application than the squeegee. But some squeegees work better than others. And there are right ways and wrong ways to use this simple tool. This video clip reviews squeegee selection, squeegee care and squeegee technique. Click to Link

Wet Applications. Dry applications are typically recommended for most vinyl applications. For those exceptions to the rule, this instructional video explains the right way to perform a wet application. Click to Link

Application of Window Graphics. Installing vinyl graphics on glass can be challenging, because the adhesive aggressively grabs onto this high energy surface. Repositioning graphics on window is generally difficult, if not impossible. This instructional video explains how to dry apply window graphics right the first time. It also describes the necessary steps required for surface preparation. Click to Link

Transferring Frosted Window Graphics Films.  Because frosted window films are highly textured, transferring cut vinyl graphics can be problematic. This video provides direction in selection of the right application tape and how to apply these films quickly, easily and without problems. Click to Link

3-Step Surface Prep. This instructional video describes how to properly clean the surface of a vehicle before applying pressure sensitive vinyl graphics to a trailer or doing a full wrap of a car or van. This three step surface prep involves detergent washing, solvent cleaning and a final wipe down with IPA. Click to Link

Vinyl Application Over Rivets. Applying vinyl graphics on vehicle surfaces with rivets is challenging for most sign makers. Vinyl failures to these surfaces are all too common. This video demonstrates some tips and procedures, used by professional decal installers, which will make these demanding applications easier and more trouble-free.  Click to Link

Vinyl Application to Corrugations. Learn how to apply vinyl graphics to corrugations in a relaxed state. Forcing films into the valleys of corrugations puts too much mechanical stress on the film. Sooner or later, the vinyl will lift or tent in valleys. Click to Link

Applying Air Egress Vinyls. Vinyl films with air egress release liners have almost eliminated bubbles and wrinkles from applied graphics. Air egress release liners with their highly textured surface structure are problematic. Not much will stick to these liners other than the vinyl film. At RTape our best premask solution for air egress liners is a special Conform® tape called 4761RLA. Click to Link

About Jim Hingst: After fourteen years as Business Development Manager at RTape, Jim Hingst retired. He was involved in many facets of the company’s business, including marketing, sales, product development and technical service.

Hingst began his career 42 years ago in the graphic arts field creating and producing advertising and promotional materials for a large test equipment manufacturer.  Working for offset printers, large format screen printers, vinyl film manufacturers, and application tape companies, his experience included estimating, production planning, purchasing and production art, as well as sales and marketing. In his capacity as a salesman, Hingst was recognized with numerous sales achievement awards.

Drawing on his experience in production and as graphics installation subcontractor, Hingst provided the industry with practical advice, publishing more than 150 articles for  publications, such as  Signs Canada, SignCraft,  Signs of the Times, Screen Printing, Sign and Digital Graphics and  Sign Builder Illustrated. He also posted more than 325 stories on his blog (hingstssignpost.blogspot.com). In 2007 Hingst’s book, Vinyl Sign Techniques, was published.  Vinyl Sign Techniques is available at sign supply distributors and at Amazon. 

Slides of Jim's Artwork

© 2016 Jim Hingst